![]() ![]() If your dashboard is running outside your LAN, you would need a method to expose the camera image externally from your LAN. The URL format for all systems running on the same LAN is: Hence why you put the BI URL in that tiles config. The browser display showing the dashboard is what calls to the URL for the BI image. Your recent learning of how the dashboard image tile is correct. The BIT Add-ons was developed in response to a member requesting certain weather results be modified after they are gathered. This wiki article will outline what the Blue Iris Tools Add-ons feature does, how it works and how to use it. ![]() You can find more information on this option by searching this forum.Īnother way of monitoring your BI app would be to use BI Tools. It can monitor your BI application and it also has a driver for Hubitat. There’s an old application called Event Ghost that you can install on your BI PC. If you just want to monitor the BI application there are multiple ways of doing this, but not all of them integrate with Hubitat. You could also add some notification logic to the rule and have it send you a push notification. If you don’t want to automate the restart process you could replace the smart plug with a virtual switch that you could put on your dashboard. The suggestion I made will monitor the PC. Any ideas on directly monitoring Blue Iris? You can live view the camera on Blue Iris now.So, I am back to square one. Step 4: Enter the camera's password, click OK. Step 3: After searching is done, click Close. Step 2: Click Find/inspect to search the camera, select the camera and click OK. Method 3: Scan the camera in LAN via ONVIF Protocol For example, if you add a camera with channel 2, then the channel number should be changed to 1 in the URL. The channel starting from 0 in the URL is counted as the first channel on the NVR. When adding cameras on different channels from the NVR, the steps are the same as adding a single camera, just repeat the same steps to add with the same IP (the IP address of the NVR) address, and only need to pay attention to modifying the channel field of the URL. If you can’t find the corresponding model for Model settings, just use the first default *model, no modification is required, and the model is not required to be correct.Ĭ. Cameras with a resolution of 8MP and above can only use the sub-stream to live view, because when you use the Reolink protocol to add a camera, you actually use the RTMP protocol, while RTMP does not support the h.265.ī. Note: when you use Reolink protocol to add a camera, please pay attention to the following points.Ī. You can live view the camera on Blue Iris now. ![]() Type your camera’s username ( admin by default) and password in the URL, click OK. Make sure the RTSP and ONVIF port numbers are the same as your camera’s. Enter the camera IP address and password. Step 2: Choose Reolink as a protocol for the Make setting. Step 1: Launch Blue Iris, right-click to choose Add New Camera, and click OK to add a camera in LAN Method 2: Add the camera via Reolink protocol Enter the camera IP address and password, and make sure the RTSP and ONVIF port numbers are the same as your camera’s, click OK. Confirm Onvif protocol is selected by default for Make Setting. Launch Blue Iris, right-click to choose Add New Camera, and click OK to add a camera in LAN Method 1: Add the camera via ONVIF Protocol Manually Note: You can also open the ports via Reolink NVRs or via the web browser, see: How to Configure Reolink Ports Settings. After opening the ports, do not forget to Save your configurations. Note: TrackMix Wired LTE can only support this feature when using wired connection.īefore getting started, login to your device on the Reolink Client, go to Device Settings > Network > Advanced > Server settings to open relevant ports for the device. Applies to: All Reolink NVRs and cameras except all battery-powered cameras, E1 and Lumus. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |